Why Does My Rolls Royce Phantom Key Fob Not Work?
The Rolls-Royce Phantom conveys wealth and the status of a car. Its massive waterfall grille and classic upright proportions are instantly recognizable. It is also among the most expensive cars in the world.
The rolls royce key fob may stop working due to many reasons. A dead coin battery is the most common reason, but other causes include water damage or receiver modules.
Battery
The coin battery is often the reason for the key fob of a Rolls-Royce Phantom not functioning. It is crucial to keep in mind that the key fob may also stop working due other reasons, like water damage or worn buttons. Other causes include signal interference, bad battery contacts, and keys that aren't paired which require changing the programming. Consult a locksmith if the key fob isn't functioning. A locksmith can pinpoint the issue quickly and provide a quick fix.
It is important to protect the battery from dirt and moisture so that it's functioning. This is why it is recommended to always make use of a waterproof key fob case when driving. It is also advisable to remove battery from key fob prior to cleaning or washing it. Additionally, the chip inside the key fob is extremely sensitive to water and shouldn't be exposed to salty or soapy water. If the key fob is prone to be exposed to water, make use of electronic cleaner or isopropyl to avoid damage.
The battery pack of the Phantom EE is a unique power system that features numerous advancements. This sets it apart from other luxury cars powered by traditional power systems. A "power reserve dial", for example it has been added to the dashboards to inform drivers of the vehicle's current power condition. This is a novel design feature, which is designed to challenge conventional car-related paradigms and showcase the potential of alternative drivetrain technology.
This electric powertrain offers the benefit of allowing charging without a physical connection between car and charging station. This is done by using induction, a method that involves the transfer of power over two surfaces: an induction pad on the ground and an induction module underneath the battery pack.
The re-charging process takes place in two phases, with a capacity of 13.5kW per phase and a total charge capacity of 71kWh. It is the largest battery for a passenger car in the world. In addition the Phantom EE is fitted with three separate charger units that allow for single-phase and three-phase charging as well as regenerative braking.
Contacts
If your Rolls Royce Phantom key fob was not working, it could be due to an unresponsive battery or worn buttons or other causes. Fortunately, the issue is usually fixable. You may also try reprogramming your key fob or replacing the battery 12 volt. If the problem persists, the receiver module might be malfunctioning. TheKeyLab is used by the remote keyless system to communicate with other electronics onboard via radio signals. If the receiver module is damaged it will cease communicating with the key fob as well as other onboard electronics.
If you are having issues with your key fob, ensure that the battery contacts are dry and clean. The metal clips that hold the button cell battery in place and complete the circuit can be damaged by wet or dirty hands. If the battery is old and needs to be replaced, it is recommended to replace it with a brand new one that is the same voltage and size. If you replace the battery, make sure to scrub the contact surfaces with ruby alcohol or electronic cleaner prior to reassembling the key fob.
The key fob of the Rolls Royce Phantom has an electronic chip that sends signals to the remote keyless system module. The module converts the signals into commands which the car can comprehend. This is how the car knows that you need to open doors or retract the "flying woman" hood ornament in the grille.
If the key fob has been exposed to water, you should immediately remove it from the vehicle and wash the electronic chip with isopropyl alcohol, or electronic cleaner. If you don't, the chip will likely be damaged.
Water damage
The key fob is made of rubber seals that prevent the chip's electronic components from being exposed. This makes it impervious to splashes and rain but not the type of deep immersion that might be experienced when you drop your key into a puddle or drop it in the ocean. If the fob is wet the chip might be fried. You will need to replace it.
Even if you haven't dropped your key fob into the water but it has been affected by a wet dog or washing machine, or perhaps soapy handwashing, don't despair since your phantom roll royce key fob may be usable. You can save money by following simple steps.
The first step is to remove the key fob and dry it completely. If you are able, remove the battery and use compressed air to eliminate any excess moisture. After you've completed this, allow it to dry for a few more days before using it.
If your key fob tends to get wet, you should think about purchasing a waterproof case to protect it from damage. It's also a good idea to keep a spare key on hand to ensure that you don't need to wait around until the fob is dry out.
Your Rolls Royce Phantom remote key may stop working in some cases due to interference, or an inactive battery. This problem is often caused by objects, poor weather conditions, or transmitters operating on the same frequency your remote.
Keep your key fob far away from these sources. If you can't avoid these sources of interference, you could try moving your car to a different location or reprogramming your remote. If you can't fix the issue yourself, it's best that you consult an expert technician. They can identify the issue and determine if it's mechanical or electrical fault.
Reprogramming
The key fob on your Rolls Royce Phantom plays a crucial part in the security system of your vehicle. It relays commands to the receiver module, which then transmits them to the vehicle's central locking mechanism. It can be extremely frustrating and expensive if the key fob stops functioning. There are a few basic things you can try to get your key fob to work again.
The first thing you need to look into is whether the battery inside the key fob is dead. It is a common cause of Phantom key fob not locking or unlocking and typically signs of deterioration such as an insufficient range. Replace the battery by one of a fresh model with the same voltage, size and specification. Also, make sure the metal retaining clips that keep the battery in place aren't loosened.
Another possibility is water damage. The rubber seals on the key fob block water from getting to the electronic chip, but in the event that the seals have been damaged by salty or soapy water, they may fail. If this happens, take the battery out and clean it with isopropyl alcohol or an electronic cleaner. Dry the battery thoroughly before putting it back in the fob.
If the key fob isn't working, it could be an indication that the receiver module has suffered a malfunction. The best way to diagnose this is to connect an diagnostic scanner to the OBD port on the dashboard of your Phantom. The scanner will request details about your vehicle, including the year, model and engine type. You will also be asked to enter the code from your key fob.
Signal interference is another possible cause. This could be caused by objects, weather conditions or transmitters that operate on the same frequency. The remote control will work when you are near the Phantom but not from a distance. This can be fixed by removing any obstructions that might be blocking the signal or by moving the Phantom further away from the transmitters.